燃油跨多隔舱流动及晃动特性分析

为获得输油过程中燃油流通能力及弹射起飞激励下的晃动特征,通过采用有限点集法对多隔舱油箱进行了数值模拟。研究结果表明：有限点集法可以清晰捕获燃油流动和晃动的自由液面特征。油箱载油量影响晃动的程度,油量减少则液面变化剧烈,重心发生大范围移动。隔舱框板的开孔面积是影响流通能力的重要因素,当其在±10%范围内变化时,流动阻力及能量耗散差异显著,这在一定程度上揭示了框板开孔与晃动抑制之间的内在机理,为多隔舱框板的工程设计和流体晃动阻尼理论研究提供重要参考。     

Numerical investigation of the impact of asymmetric fuel injection on shock train characteristics

Numerical simulations are carried out to investigate the impact of asymmetric fuel injection on shock train characteristics using the commercial-code FLUENT. The asymmetry of fuel injection is examined by changing the fuel flow rates of the upper and lower wall fuel injectors. The numerical approach solves the two-dimensional Reynolds-averaged Navier–Stokes (RANS) equations, supplemented with a k-ω model of turbulence. As a result, different ways of fuel injections will always lead to shock train transitions, with the variations of shock train structure, strength and leading edge position. For symmetric fuel injection, the flowfield of the isolator is quite asymmetric with the boundary layer of the upper wall side developing much stronger than that of the lower wall, which is due to the heterogeneity of the incoming flow. Regarding to asymmetric fuel injection with more of lower wall side, though the pressures in the combustor are nearly the same, the first shock of the shock train converts between ‘Distinct symmetric X type shock’ and ‘Obscure and weaker asymmetric shock’ and the shock train leading edge moves upstream with the increase of the asymmetry level. With regard to asymmetric fuel injection with more of upper wall side, ‘incomplete asymmetric X type shock’ occurs and the shock train structures keep nearly the same with low level of fuel injection asymmetry. Unexpected results like unstart will happen when increasing the level of fuel injection asymmetry. And the isolator will come back to normal state by decreasing the differential of upper and lower wall sides fuel injections.     

直升机燃油系统增压转自吸供油动特性

通过某型燃油系统增压供油转自吸供油试验,研究了发动机入口处的流量历程。在试验研究和直升机燃油系统增压转自吸供油机理基础上,利用Flowmaster软件建立了某典型直升机燃油系统仿真模型,仿真结果与试验结果吻合较好,验证了模型的正确性。在此基础上,研究了直升机燃油系统增压转自吸供油动特性。结合仿真结果,分析了增压泵出口单向阀的弹簧预紧力、弹簧刚度对发动机入口燃油流量、压力的影响,为燃油系统零部件选型及参数确定提供参考。     

膏体推进剂冲压发动机一次燃烧试验

针对额定流量和流量调节条件下膏体冲压发动机一次燃烧组织稳定的要求,提出了一种燃面自适应燃烧组织模式,设计了一次燃烧组织试验系统,进行了一次燃烧组织试验。试验结果表明,推进剂输送稳定,点火时序和推进剂输送时机合理,防回火措施有效,燃烧室压强经过调整后能够稳定在设计值附近。燃面自适应燃烧组织模式可以实现燃面的自适应调节,使推进剂输送和燃烧保持平衡,保证发动机的一次燃烧稳定。     

微型燃气轮机喷嘴射流和雾化特性研究

为在微型燃气轮机内营造低氧贫燃氛围以实现液体燃料的节能减排,利用可适性多普勒激光测速仪APV/LDV对改造喷嘴附近截面进行了测量和分析,用以考查近喷嘴处的气液混合夹带情况以及雾滴尺寸及分布。结果发现：增加外部涡旋气流后,喷孔附近雾滴的动量增大,雾锥内出现一小回流区,对应湍流度较大区域附近;燃烧时较大切向动量及湍流度利于空气与周围高温烟气迅速混合形成低氧环境,并和雾滴掺混进行热量和动量的传递;喷孔出口雾化角增大,使得雾滴更加分散,利于雾化、气液混合和传热传质;所有实验工况雾滴平均直径低于50μm,且为偏高斯分布。该研究为液体燃料喷嘴的设计提供了参考,可作为微型燃气轮机燃烧室热态反应物流场的参考依据。     

Experimental Study on Emission Performance of an LPP/TVC

A key issue in the commercial aircraft engine design is environmental acceptability, and designers are continually challenged to reduce emissions. In this paper, an experimental investigation is performed to evaluate the emission performance of a liquid-fueled trapped vortex combustor (TVC) under lean premixed prevaporized (LPP) mode. When operating as an LPP system, a TVC is fueled both in the cavities and in the main stream. The correlations between the emission performance and the total excess air ratio, the positions (4 positions) of the fuel injectors in the main stream, and the inlet temperature are obtained. Experi- mental results show that both the volume concentrations of unburnt hydrocarbon (UHC) and NOx (NO, NO2 usually grouped together as NOx) increase with the increase of total excess air ratio from 1.5 to 3.0; the emission performance relies heavily on the position of the main stream injector, and the best performance is achieved at Position 4 in the experiments; the increase of the inlet temperature impacts on the emission performance positively; the smallest volume concentrations of UHC and NOx obtained in the experiment are 94×10 6 and 2.3×10 6 respectively. This paper validates the feasibility of low emissions for an LPP/TVC and provides a reference for further optimization of TVCs.     

微型定容多次燃油喷射系统高速响应特性仿真

针对小排量发动机转速范围大、工作循环喷油量小的特点,提出了一种微型定容多次燃油喷射系统结构,建立了系统电、磁、液、机耦合模型,仿真计算了从输入电压到喷射输出的动态响应特性,分析了影响系统高速特性的关键因素.结果表明:该喷射系统响应频率可达到1000Hz,响应时间可以满足小排量发动机最高转速要求,具备工程可实现性.      

气氢/气氧同轴剪切单喷嘴燃烧室壁面热流计算与分析

以气氢/气氧为推进剂,采用数值模拟方法,研究了同轴剪切喷嘴设计参数——氢氧速度比和氧压降比对单喷嘴燃烧室内燃烧过程和壁面热载的影响,并将绝热壁面条件、等温壁面条件的计算结果与试验结果进行了对比分析,结果表明:氢氧速度比增大,燃烧性能提高,壁面热载增加;氧压降比增大,燃烧性能下降,壁面热载减小;相比采用壁面绝热燃气温度,采用热流预示燃烧室壁面热载与真实情况更为接近.      

固液火箭发动机工作过程三维数值仿真

根据固体燃料壁面与气相间的流固耦合得出了固体燃料燃速模型,对采用星形装药的H₂O₂/HTPB(hydroxyl-terminated polybutadiene)固液火箭发动机进行了燃烧流动三维数值仿真,得到了流场参数的分布及不同位置的固体燃料燃速,与二维轴对称仿真结果进行了对比.计算结果表明:装药截面的火焰层形状与装药星孔型面形状相似,但火焰层厚度与位置在星根与星角处存在差异;随着轴向位置的增加,氧化剂不断消耗,火焰层向通道中心移动;固体燃料燃速与氧化剂流率及不同装药位置有关,其大小随氧化剂流率的增加而增加,星根处燃速比星角处大;在相同氧化剂流率下,三维星形装药比二维轴对称装药的平均固体燃料燃速大.      

加力燃油泵隔舌倒圆抑制分离的数值模拟

采用动态亚格子应力模型对加力燃油泵内非定常流场进行大涡模拟,探讨了原隔舌空蚀机理,并研究了不同倒圆半径下泵隔舌附近的瞬时流动规律及流量扬程特性.计算结果表明:小流量工况原隔舌处分离产生的强剪切涡会诱发空化,涡脱落形成的分离再附位置与空蚀破坏核心区域相符;小流量工况下,隔舌倒圆在扩散管内形成转向涡,消除了隔舌壁面分离绕流及附着剪切涡,4mm倒圆半径可以避免空化;设计流量范围内隔舌倒圆提高了泵出口扬程,流量越小扬程增幅越大,小流量工况时扬程增幅达3%.